150 W Glass Laser Tube

General Features;

- Laser cutting, Engraving and marking is used in the process.
- Suited to daily working hours.
- Typically, textile cutting, paper cutting, wood, MDF, plywood, glass, leather, cardboard, paper used in the business sector.

Type
-A closed circuit Co2 Class IV laser beam Invisible /Wavelength
-10.6 Micrometers
Power
-A maximum of 150 watts, the standard power of 150 watts, 140 watts power guaranteed.
Working Current
-Ideal 20 MA, 28 Ma maximum
Working Conditions
-10C-40C heat and 10% to 60% humidity range (Ideal operating range 15C - 25C)
Lifespan
-8000 hours (Ideal current value at room temperature, and with good cooling)
Cooling
-10 liters per minute with the water cycle
Suitable power supply
-Vera PS-M or Reci P14
Dimensions and weight
-Diameter 6cm, length 125cm, 6 kg

Warranty
- Are warranted for 6 months from the date of sale.
- Adequate cooling, correct use and the terms of use are followed to ensure that the power supply should be taken.
- With the problems that will occur during the warranty period, our technical staff after check in will be done by the manufacturer will be contacted.
- Free exchange accepted by the manufacturer for the products is made.
- The tubes are replaced with new ones generating power for free power guaranteed under.
- The change is made within the warranty period, products are re-the warranty period is not given, the first product based on the expiration of the warranty period.
- The change that occur during shipping or service costs, shall be borne by the buyer

Security
- The laser beam is invisible. Your body must not touch never.
- For your safety, protection glasses should be worn to 10.6 micrometers Co2.
- Positive high voltage from the point against electrical shock, be careful.

Maintenance
- The workspace of the laser tube smoke, dust, and dirt should be protected. Dirty lens on the laser tube should be in front of the exit.
- Very precise when cleaning is necessary should be treated. Only pure alcohol or a laser lens cleaning kits should be used.
- First by squeezing and then by blowing air cleaned the dust dirt solidified on alcohol or cleaning solution to purify you must wait.
- Afterwards, the paper or gently with Optical Cleaning Optical Cleaning Kits should be cleaned. -30cm clear acrylic test tube is carried away by the laser beam after the beam is recommended.

Instructions
- Vera, which is an ideal power source PS-a power source for use with P14 or equivalent with M Reci tube will hold the highest levels of life.
- The rear of tube circulating water (not light) from the front part (light out) flows in the direction of make sure
- Make sure you use distilled water and change your water once a month.
- Try to remain at room temperature of cooling water.
- Your use of the cooling device will help you use your tube for long life.
- Between 40C and 10C degrees working environment humidity 10% and 60% the product can operate between. This heat and humidity values affect the strength of the product.
- The difference between the temperature of cooling water with the ambient temperature should be 10C ideal.
- The ambient temperature is 22C the water through the laser tube 30 to be in the area, which is ideal. Water temperature should not be colder.
- Water should be 35C ambient temperature 25C degrees in an area that is. We recommend you to set up your cooler to keep constant at 25C in summer.
- The rear portion of the tube (not light) high voltage power supply positive connect the cable, cable is usually red colored.
- Connect the negative cable to the front side. The negative cable connects to the AMP then from the tube, and then reaches to the power source.
- The product 2C-40C, between store. In case of the possibility of being cold at night drain the water out. In the case of the inside of the tube from freezing water will crack.
- Warm 40C degrees in the areas above, due to the expansion of the gas within the tube may leak from the source points.

Technical Support and Warranty;

- 2 year warranty, a pioneer in providing technical support and spare parts.
- The head and the variety of our products according to the system, the warranty period varies.
- Our expert product representatives will talk you through the options most appropriate for you