90 W Glass Laser Tube

General Features;

Laser engraving, marking and cutting is used.
Suited to daily working hours. 
Typically, textile cutting, paper cutting, wood, MDF, plywood, glass, leather, cardboard, paper, marble, such as is used in branding and the business sector.

Type : A closed circuit Co2 Class IV laser beam Invisible
Wavelength Micrometer -10.6 Power -100 Watts maximum, 90 watts standard power, 85 watts of power is guaranteed.
Working Current - Ideal 20 MA, maximum 2
Working Conditions - 10C-40C heat and 10% to 60% humidity range (Ideal operating range 15C - 25C) Lifespan Minus 8000 Hours (ideal current value at room temperature, and with good cooling)
Cooling The water cycle - 10 liters per minute with
Suitable power supply - Vera PS-M or Reci P14 Dimensions and weight Diameter 6cm, length 125cm, 6 kg

Quarantee

- Are warranted for 6 months from the date of sale.
- Adequate cooling, correct use and the terms of use are followed to ensure that the power supply should be taken.
- With the problems that will occur during the warranty period, our technical staff after check in will be done by the manufacturer will be contacted.
- Free exchange for the products made by the manufacturer is accepted.
- The tubes are replaced with new ones generating power for free power guaranteed under.
- The change is made within the warranty period, products are re-the warranty period is not given, the first product based on the expiration of the warranty period.
- The change that occur during shipping or service costs, shall be borne by the buyer.

Security,
- The laser beam is invisible. Your body must not touch never.
- For your safety, protection glasses should be worn to 10.6 micrometers Co2.
- Positive high voltage from the point against electrical shock, be careful.

Maintenance,
- The workspace of the laser tube smoke, dust, and dirt should be protected. Dirty lens on the laser tube should be in front of the exit.
- Very precise when cleaning is necessary should be treated. Only pure alcohol or a laser lens cleaning kits should be used.
- First by squeezing and then by blowing air cleaned the dust dirt solidified on alcohol or cleaning solution to purify you must wait.
- Afterwards, the paper or gently with Optical Cleaning Optical Cleaning Kits should be cleaned.
- 30cm clear acrylic test tube is carried away by the laser beam after the beam is recommended.

Instructions,
- Vera, which is an ideal power source PS-a power source for use with P14 or equivalent with M Reci tube will hold the highest levels of life.
- The rear of tube circulating water (not light) from the front part (light out) flows in the direction of make sure.
- Make sure you use distilled water and change your water once a month.
- Try to remain at room temperature of cooling water.
- Your use of the cooling device will help you use your tube for long life.
- Between 40C and 10C degrees working environment humidity 10% and 60% the product can operate between. This heat and humidity values affect the strength of the product.
- The difference between the temperature of cooling water with the ambient temperature should be 10C ideal.
- The ambient temperature is 22C the water through the laser tube 30 to be in the area, which is ideal. Water temperature should not be colder.
- Water should be 35C ambient temperature 25C degrees in an area that is. We recommend you to set up your cooler to keep constant at 25C in summer
- The rear portion of the tube (not light) high voltage power supply positive connect the cable, cable is usually red colored.
- Connect the negative cable to the front side. The negative cable connects to the AMP then from the tube, and then reaches to the power source.
- The product 2C-40C, between store. In case of the possibility of being cold at night drain the water out. In the case of the inside of the tube from freezing water will crack.
- Warm 40C degrees in the areas above, due to the expansion of the gas within the tube may leak from the source points.

 

Technical Support and Warranty:

- 2 year warranty, a pioneer in providing technical support and spare parts.
- The head and the variety of our products according to the system, the warranty period varies.
- Our expert representatives will talk you through the product options most appropriate for you.